Os-engines 95AX Bedienungsanleitung

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section

18INSTALLING THE GLOWPLUGInstall washer on glowplug and insert carefully into cylinder-head, making sure that it is not cross-threaded bef

20Suggested fuel tank capacity is approx 350cc. This will allow 10minute flights.FUEL TANK LOCATIONBe sure to use a pressurized fuel system by co

22MIXTURE CONTROLSThe Needle ValveWhen set to produce maximum power at full throttle, this establishes the basic fuel/air mixture strength. The c

24! STARTINGBe sure to use an electric starter to start the engine.Fill the fuel tank with fuel. When filled, prevent the fuel from

26Attention :Do not choke the carburetor air intake when applying the starter. This could cause an excessive amount of fuel to be draw

28During subsequent flights, the needle-valve can be gradually closed to give more power. However, if the engine shows signs of running

30IDLING ADJUSTMENT CHARTStart the engine.Make sure that the throttle isfully open.Adjust the needle-valve.Close the throttle gradually.Set the idle s

32REALIGNMENT OF MIXTURE CONTROL VALVESUBSEQUENT STARTING PROCEDUREOnce the optimum needle-valve setting has been established (see page 29,

34123SymptomFactorCauseCorrective actionRecharge the electric starter battery.Recharge lead-acid or ni-cad type cell or replace dry battery. (Note: A

36CARE AND MAINTENANCEPlease pay attention to the matters described below to ensure that your engine serves you well in regard to performan

2Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of h

3875AX ENGINE EXPLODED VIEWType of screw C...Cap Screw 7987111079871160M3x8M3x16CAP SCREW SETS(10pcs./sets)Code No.SizePcs. used in an engineCylinder

4061A CARBURETOR EXPLODED VIEWType of screw N...Round Head Screw S...Set Screw12457S.M3X3363-13-27-17-288-1N.+M3x69N.+M3.5x6104161A CARBURETOR PARTS

42C.M3x16C.M3x814567891012111314151631721895AX ENGINE EXPLODED VIEWType of screw C...Cap Screw 7987111079871160M3x8M3x16CAP SCREW SETS(10pcs./sets)Cod

4412457S.M3X3363-13-27-17-288-1N.+M3x69N.+M3.5x61061C CARBURETOR EXPLODED VIEWType of screw N...Round Head Screw S...Set Screw4561C CARBURETOR PARTS

46(71905200)(71531000)(26625340)(71531010)O.S.GLOW PLUGO.S. GENUINE PARTS & ACCESSORIESRADIAL MOTOR MOUNTNON-BUBBLEWEIGHTSILENCER EXTENSIONADAPTOR

48Displacement Bore Stroke Power output atrecommended R.P.M. rangeRecommended R.P.M. rangePower output Practical R.P.M. WeightSPECIFICATIONSDimension

50MEMOC Copyright 2009 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan.60092190 070901TEL. (06) 6702-0225FAX. (06) 6704-27226-

4NOTESThis engine was designed for model aircraft. Do not attempt to use it for any other purpose.Mount the engine in your model se

6NOTESAdjust the throttle linkage so that the engine stops when the throttle stick and trim lever on the transmitter are fully retarded. A

8NOTES WHEN APPLYINGAN ELECTRIC STARTERDo not over-prime. This could cause a hydraulic lock and damage the engine on application of the elect

10BASIC ENGINE PARTSCylinder headCarburetor Type 61A CrankshaftPropeller nutPropeller washerDrive HubCrankcaseCover PlateGlowplugBeam MountLock nutMAX

12FUELThe 75AX and 95AX should be operated on a methanol based fuel containing not less than 18% (volumetric) castor oil, or a top quality

148mmTOOLSHEX ScrewdriverSCREWDRIVERNecessary for engine installation.1.5mm, 2.5mm, 3.0mmNecessary for carburetor adjustments.Phillips ScrewdriverNo.2

16How to fasten the mounting screws.Hardwood mounting beamsRadial motor mount (cast aluminum)Tighten second nutfirmlydown onto first nut.Tighten this