Os-engines 18TM Revo Bedienungsanleitung Seite 1

18TM w/11K-R & T-Maxx Revo ManifoldMAX-OWNER'S INSTRUCTION MANUALIt is of vital importance, before attempting tooperate your engine, to read

Model engine fuel is poisonous. Donot allow it to come into contact withthe eyes or mouth. Always store it in aclearly marked container and out ofthe

BASIC ENGINE PARTSTOOLSHEX WRENCHNecessary for engine installation.1.5mm, 2mm, 2.5mm, 3mmSCREWDRIVERNecessary for carburetor adjustments.No-1, No.2,et

CARBURETOR CONTROLSFour adjustable controls are provided onthis carburetor.Needle ValveThrottle StopScrewMixture Control ValveThermo InsulatorMetering

FACTS ABOUT GLOWPLUGSSince the compatibility of glowplug and fuel may havea marked effect on performance and reliability, it maybe worthwhile to choos

INSTALLATIONInstall the flywheel and clutch.First, remove the engine, installed as standard,with the engine mount.13

Install the engine on the engine mount withearth wire.Install the electric starter taken from theoriginal engine.Install the manifold supplied with th

Adjust the aluminum stopper end so that thethrottle linkage may be made correctly.15

Finally, insert the wire for glow plug heating inthe glow plug.16

STARTING THE ENGINE & RUNNING-IN ('Breaking-in')For long life and high performance, everyengine needs to be 'run-in' or '

The carburetor of this engine is set at startingsetting when the engine leaves the factory.Switch on the transmitter, and check that all thelinkage mo

CONTENTSSAFETY INSTRUCTIONS ANDWARNINGS ABOUT YOUR O.S. ENGINE... 2-5ENGINE CONSTRUCTION... 6NOTES WHEN APPLYING AN ELECTRI

Note:If the engine should need to be disassem-bled (e.g. for cleaning or minor parts re-placement), it is advisable to return the nee-dle-valve to the

Needle ValveFINAL ADJUSTMENTFinal adjustment should be carried out only afterthe running-in has been completed.Throttle Stop ScrewCloseMore fuel Less

With the engine running, close the throttleand allow it to idle for about five seconds,then reopen the throttle fully. If, at this point,the engine pu

Finally, beyond the nominal break-in period,a slight readjustment toward a leaner needlesetting may be required to maintainmaximum performance.The cor

CARE AND MAINTENANCE1 .The minute particles of foreign matter, thatare present in any fuel may, by accumulatingand partially obstructing fuel flow, ca

5. Finally, when cleaning the exterior of theengine, use methanol or kerosene. Do notuse gasoline or any solvent that mightdamage the silicone fuel tu

CHECKING THE ENGINEEngine will not develop normal performanceafter long time running due to wearing of parts.It is suggested to replace necessary part

TROUBLE SHOOTINGEngine fails to fire.Fuel tank is empty.Fuel not reaching the engine.Glowplug element is burnt out.Glowplug battery dischargedClogged

Engine fires intermittently but does not run.Insufficient fuel in the tank.Fill the tank with fuel.Deteriorated glowplugReplace glowplug.Clogged fuel

Unsuitable glowplugUnstable idleUse suggested glowplug in the instructions.Unsuitable fuelExtremely light flywheelDo not use extremely high nitro or l

SAFETY INSTRUCTIONS AND WARNINGS ABOUTYOUR O.S. ENGINERemember that your engine is not a "toy", but a highly efficient internal-combustion m

Poor r.p.m, dropToo much throttle opening at idle.Incorrect setting of transmitter Exponential function.Incorrect carburetor fittingFit carburetor sec

ENGINE EXPLODED VIEWC.M3X16121614M.+M2.6X735461513712118109*Type of screw C -Cap Screw M—Oval Fillister-Head ScrewF'-Flat Head Screw N"-Roun

ENGINE PARTS LISTThe specifications are subject to alteration for improvement without notice.Manifold Spring (2pcs.)Exhaust Manifold forT-Maxx RevoExh

CARBURETOR EXPLODED VIEW32*s Type of screwC...Cap Screw M...0val Fillister-Head ScrewF...Flat Head Screw N...Round Head Screw S...Set Screw2-122-233-1

CARBURETOR PARTS LISTThe specifications are subject to alteration for improvement without notice.33Carburetor Rubber GasketThermo InsulatorThrottle Le

RACING ENGINE PARTSO.S. GENUINE PARTS & ACCESSORIESO.S. Glow PlugLC3(71653000)Exhaust Seal Ring(2pcs.)(21427200)Manifold Spring (2pcs.)(72106172)L

THREE VIEW DRAWING35Dimensions (mm)SPECIFICATIONS3.0cc (0.183cu.in.)16.0mm (0.629in.)15.0mm (0.590m.)3,000-34,000 r.p.m.1.6ps/29,000 r.p.m.233g (8.22o

GUARANTEED TOKEEP YOUR R/C CARRUNNING WELLKEEP IT CLEANDirt is the most common way to ruin your engine. If it gets inside,the dirt will act just like

KEEP IT COOLIf you run your engine good and hot, you'll have a nice chunck ofuseless aluminum in a short time.•Running the engine hot causes the

GUARANTEED TOKEEP YOUR R/C CARRUNNING WELL(Continued)(CONTINUED)Here's how to prevent rust;• At the end of the day's running, pull the fuel

• Model engine fuel is poi-sonous. Do not allow it tocome into contact with theeyes or mouth. Always storeit in a clearly marked con-tainer and out of

(CONTINUED)This kind of damage is not covered under the warranty.• If the flywheel can't be tightened onto the engine without it tryingto turn ov

40

LIMITED WARRANTYYour engine is guaranteed to be free of defects in parts and workmanship for a period of 2 yearsfrom the date of purchase when returne

6-15 3-Chome Imagawa Higashisumiyoshi-kuOsaka 546-0003, Japan TEL. (06) 6702-0225FAX. (06) 6704-2722URL: http://www.os-engines.co.jp© Copyright 2004 b

This engine is intended for model cars.Do not attempt to use it for any otherpurpose.Mount the engine in your modelsecurely, following the manufacture

Take care that the glowplug clip orbattery leads do not come into contactwith rotating parts. Also check that thelinkage to the throttle arm is secure

ENGINE CONSTRUCTIONWith this engine, the piston willfeel tight at the top of its stroke(TDC) when the engine is cold.This is normal. The cylinder bore

NOTES WHEN APPLYINGAN ELECTRIC STARTERDo not over-prime. This couldcause a hydraulic lock and damagethe engine on application of theelectric starter.I

ABOUT THE ENGINEThis engine is designed especially to power the T-Maxx Revo. Purposelly designed LC3 glow plug issupplied with the engine for improved